Measuring Instruments Archives - Page 27 of 82

Clear graduations on satin-chrome finish.
Stainless tempered.

SPECIFICATIONS

Metric Wide Rigid Rules

Order No.	Graduations	Range	Width
182-111	1mm, 0.5mm (on both faces)	150mm	19mm
182-131		300mm	25mm
182-151		450mm	30mm
182-171		600mm	30mm

Metric Fully-Flexible Rules

Order No.	Graduations	Range	Width
182-211	1mm, 0.5mm (on both faces)	150mm	12mm
182-231		300mm	12mm
182-251		450mm	19mm
182-271		600mm	19mm

Inch/Metric Semi-Flexible Rules

Order No.	Graduations*	Range	Width
182-302	1/16″, 1/32″, 1/64″, 1mm, 0.5mm	6″/150mm	.51″
182-303		8″/200mm	.51″
182-305		12″/300mm	.59″
182-307		20″/500mm	.59″
182-309		40″/1000mm	.59″

* Engraved on the front side only.

Inch/Metric Wide Rigid Rules

Order No.	Graduations	Range	Width
182-105	1/32″, 1/64″, 1mm, 0.5mm	6″/150mm	.75″
182-125		12″/300mm	.98″
182-145		18″/450mm	1.18″
182-165		24″/600mm	1.18″
182-106	1/50″, 1/100″, 1mm, 0.5mm	6″/150mm	.75″
182-126	1/50″, 1/100″, 1mm, 0.5mm	12″/300mm	.98″
182-107	1/10″, 1/100″, 1mm, 0.5mm	6″/150mm	.75″
182-108	1/10″, 1/50″, 1mm, 0.5mm	6″/150mm	.75″

Inch/Metric Fully-Flexible Rules

Order No.	Graduations	Range	Width
182-205	1/32″, 1/64″, 1mm, 0.5mm	6″/150mm	.47″
182-225		12″/300mm	.47″
182-245		18″/450mm	.75″
182-265		24″/600mm	.75″
182-206	1/50″, 1/100″, 1mm, 0.5mm	6″/150mm	.47″
182-226	1/50″, 1/100″, 1mm, 0.5mm	12″/300mm	.47″
182-207	1/10″, 1/100″, 1mm, 0.5mm	6″/150mm	.47″
182-208	1/10″, 1/50″, 1mm, 0.5mm	6″/150mm	.47″

Inch Wide Rigid Rules

Order No.	Graduations	Range	Width
182-101	1/8″, 1/16″, 1/32″, 1/64″	6″	.75″
182-121		12″	.98″
182-141		18″	0.71″
182-161		24″	1.18″
182-102	1/50″, 1/100″, 1/32″, 1/64″	6″	.75″
182-122		12″	.98″
182-142		18″	1.18″
182-162		24″	1.18″
182-103	1/10″, 1/100″, 1/32″, 1/64″	6″	.75″
182-123		12″	.98″
182-143		18″	1.18″
182-163		24″	1.18″
182-104	1/10″, 1/50″, 1/32″, 1/64″	6″	.75″
182-124	1/10″, 1/50″, 1/32″, 1/64″	12″	.98″

Inch Fully-Flexible Rules

Order No.	Graduations	Range	Width
182-201	1/8″, 1/16″, 1/32″, 1/64″	6″	.47″
182-221		12″	.47″
182-241		18″	1.18″
182-261		24″	.75″
182-202	1/50″, 1/100″, 1/32″, 1/64″	6″	.47″
182-222		12″	.47″
182-242		18″	.75″
182-262		24″	.75″
182-203	1/10″, 1/100″, 1/32″, 1/64″	6″	.47″
182-223		12″	.47″
182-243		18″	.75″
182-263		24″	.75″
182-204	1/10″, 1/50″, 1/32″, 1/64″	6″	.47″
182-224	1/10″, 1/50″, 1/32″, 1/64″	12″	.47″

Specially designed for standard size gauge blocks over 125mm which have two coupling holes on the body: coupling of two long gauge blocks and attachment of jaws is possible.
These accessories can also be used for CERA blocks.

SPECIFICATIONS

Set Order No.	Individual Item Order No.	Item Description	Quantity Supplied
516-605	619031	Connector A	1 pc.
	619032	Connector B
	619033	Connector C
	619034	Connector D
	619035	Connector E
	619036	Adapter	3 pcs.
	619009	Base	1 pc.
	619013	Half round jaw	One pair (2pcs)
	619018	Plain jaw	One pair (2pcs)
	619019	Scriber point	1 pc.

* Only 1 pc is supplied for each Order No. However, half round jaw, plain jaw, and tram point are supplied in a pair. (2 pcs).

Connector A

Used for directly coupling two long gauge blocks.

Connectors B and C

	Order No.	(max.)	L	Adapter Qty
Connector B	619032	90mm	126mm	2
Connector C	619033	200mm	236mm	2

Used for clamping jaws to the ends of one or more long gauge blocks in conjunction with adapters (619036). The length is highly adjustable to accommodate the variable length of a stack of regular gauge blocks that would be wrung to one of the long gauge blocks to achieve the required gaging size.

Connector D

Used for attaching a long gauge block directly to the base.

Connector E

Used for attaching a long gauge block to the base over a stack of regular gauge blocks wrung between the base and long gauge block. The length is highly adjustable to accommodate the variable length of the stack.

Base

Flatness tolerance of the finished surface 0.5µm
Flatness tolerance of the bottom surface 1µm

Plain jaw

Flatness tolerance of the ﬁnished surface 1µm

Half round jaw

Flatness tolerance of the ﬁnished surface 0.5µm

Scriber point

Flatness tolerance of the ﬁnished surface 0.5µm

Assortment of accessories for gauge blocks
For inside and outside measurement inspection of 300 to 1000 mm (every 100mm) gauge blocks, select the appropriate combination of a rectangular gauge block and an accessory.

Items		Order No.	300mm		400mm		500mm		600mm		700mm		800mm		900mm		1000mm
Items		Order No.	Inner	Outer	Inner	Outer	Inner	Outer	Inner	Outer	Inner	Inner	Inner	Outer	Inner	Out	Inner	Outer
Rectangular gauge block (nominal dimension)	200mm	611682							1	1
	300mm	611683	1	1							1	1	1	1
	400mm	611684			1	1			1	1	1	1			1	1
	500mm	611685					1	1					1	1	1	1	2	2
Connector A		619031							1	1	1	1	1	1	1	1	1	1
Connector B*1		619032	2		2		2		2		2		2		2		2
Half round jaws*2		619013	1		1		1		1		1		1		1		1
Adapter		619036	(2)		(2)		(2)		(2)		(2)		(2)		(2)		(2)

*1 Provided with adapters (2 pcs)
*2 2 pcs/set

Setting a dial test indicator to a long-gauge- block stack attached to the base with a D-type connector

Optimal for hole, narrow groove and step measurement.

Metric

Order No.	Range	Graduation	Accuracy	Stroke	Measuring force					Contact point*1	Extension rod*2	Indicator*3 (dial indicator)
Order No.	Range	Graduation	Accuracy	Stroke	Measuring force	W	T	Flatness	Mounting position of a dial indicator	Contact point*1	Extension rod*2	Indicator*3 (dial indicator)
7210	0 – 10mm	0.01mm	±15μm	10mm	1.4N	40mm	16mm	5μm	1	Provided with a needle point (No.137413)	—	2902SB for Depth Gage
7211	0 – 200mm					63.5mm				Provided with a carbide- tipped ball point (No.21JAA224)	5 pcs. (10, 20, 30, 30, 100mm)
7212	0 – 200mm					101.6mm					5 pcs. (10, 20, 30, 30, 100mm)
7213	0 – 210mm		±30μm	30mm	2.5N	63.5mm				Provided with a carbide- tipped ball point (No.21JAA225)	3 pcs. (30, 60, 90mm)	2952SB for Depth Gage
7214	0 – 210mm		±30μm	30mm	2.5N	101.6mm					3 pcs. (30, 60, 90mm)	2952SB for Depth Gage
7220	0 – 200mm		±15μm	10mm	1.4N	100mm	18mm		2	Provided with a carbide- tipped ball point (No.21JAA224)	5 pcs. (10, 20, 30, 30, 100mm)	2902SB for Depth Gage
7221	0 – 200mm					150mm	18mm		3		5 pcs. (10, 20, 30, 30, 100mm)
7222	0 – 10mm					ø16mm			1	Provided with a needle point (No.137413)	—
7223						ø25mm				Provided with a carbide- tipped ball point (No.21JAA224: 17mm) (No.21JAA226: 22mm)
7224						ø40mm
7231	0 – 200mm			5mm		63.5mm	16mm				5 pcs. (10, 20, 30, 30, 100mm)	1162T for Depth Gage (Back plunger type)

Inch

Order No.	Range	Graduation	Accuracy	Stroke	Measuring force					Contact point*1	Extension rod*2	Indicator*3 (dial indicator)
Order No.	Range	Graduation	Accuracy	Stroke	Measuring force	W	T	Flatness	Mounting position of a dial indicator	Contact point*1	Extension rod*2	Indicator*3 (dial indicator)
7217S	0 – 8”	.001”	±.002”	1”	2.5N	63.5mm	16mm	.0002″	1	Carbide ball point (No.21JZA242)	3 pcs. (1”, 2”, 4”)	2904SB for Depth Gage
7218S				1”	2.5N	101.6mm				Carbide ball point (No.21JZA242)	3 pcs. (1”, 2”, 4”)	2904SB for Depth Gage
7237T				.2”	1.4N	63.5mm				Provided with a carbide- tipped ball point (No.21JZA242: 17.8mm) (No.21JZA243: 22.9mm)	4 pcs. (.5”, 1”, 2”, 4”)	1168T for Depth Gage (Back plunger type)
7238T				.2”	1.4N	101.6mm					4 pcs. (.5”, 1”, 2”, 4”)	1168T for Depth Gage (Back plunger type)

DIMENSIONS

Note:

Caution should be exercised when exchanging a contact point of a Depth Gage (Dial/Digimatic Indicator)

If a different size contact point is mounted, displacement of the contact point from the base contact surface will be changed and as a result, measurement range may not be
A contact point cannot be mounted to a Depth Gage, if its diameter is too large for the hole diameter of the
Parallelism adjustment with the bottom face of the base is required when mounting a flat contact point such as the flat/needle or carbide-tipped contact

Caution on should be exercised when using an extension rod

If the total length of the extension rod exceeds 110mm (4.5″) use the instrument in a vertical position (contact point downward).
Use a master gage (such as Gauge blocks) to perform zero-setting when the extension rod is mounted. (Master gage is an optional accessory.)

Indicators

Indicators for a Depth Gage is used for the Depth When the indicator is exchanged and extension rod is connected longer, the contact-point may incline significantly.
Code No.543-400B / 543-402B for Depth Gage has a measuring force less than 1.5N.

The end of the main beam is hook-shaped to allow depth and thickness measurements of a projected portion or lip in a hole, in addition to standard depth measurement.
Coolant proof models achieve IP67 protection level.
Enables stable depth measurement with a resolution of 0.01mm.
ABSOLUTE Digital Caliper (Refer to page D-8 for ABSOLUTE function.)
Digital models display the compensation value by pressing the OFF switch to allow direct reading.
Slider operation of the digital models is smooth and comfortable.
Allows integration into statistical process control and measurement systems for models with measurement data output connector. Refer to page A-3.
Battery: SR44 (1 pc), 938882. For initial operational checks (standard accessory)
Battery life: Approx. 3 years under normal use (for digital models)
Optional longer extension bases are available.

SPECIFICATIONS

Metric

Order No.	Range: L₁ (L₂ and L₃)	Resolution	Accuracy*	Base (W×T)
Digimatic (LCD)
571-254-10**	10 – 160mm (0 – 150mm)	0.01mm	±0.03mm	100×6mm
571-255-10**	10 – 210mm (0 – 200mm)	0.01mm	±0.03mm	100×6mm
Analog
527-401	10 – 150mm (0 – 150mm)	0.05mm	±0.05mm	100×6.5mm
527-402	10 – 200mm (0 – 200mm)		±0.05mm
527-403	10 – 300mm (0 – 300mm)		±0.08mm

* Excluding quantizing error ** IP67 Coolant Proof model

Inch/Metric

Order No.	Range: L₁ (L₂ and L₃)	Resolution	Accuracy*	Base (W×T)
Digimatic (LCD)
571-264-10	.4” – 6.4” (0 – 6”)	.0005” / 0.01mm	±0.0015″/ ±0.03mm	100×6mm
571-265-10	.4” – 8.4” (0 – 8”)	.0005” / 0.01mm	±0.0015″/ ±0.03mm	100×6mm

* Excluding quantizing error

Metric

Order No.	Range: L₁ (L₂ and L₃)	Vernier reading	Accuracy	Base (W×T)
Analog
527-411	10 – 150mm (0 – 150mm)	0.02mm	±0.03mm	100×6.5mm
527-412	10 – 200mm (0 – 200mm)		±0.03mm
527-413	10 – 300mm (0 – 300mm)		±0.04mm

DIMENSIONS

Applications

Optional accessories for digital models
For details, refer to page A-21. Connection cables for coolant proof models
05CZA624: SPC cable with data button (1m)
05CZA625: SPC cable with data button (2m)

USB Input Tool Direct
06ADCV380A: SPC cable for USB-ITN-B (2m)
Connecting cables for U-WAVE-T
02AZD790A: SPC cable for U-WAVE with data button (160mm)
02AZE140A: SPC cable for footswitch

Standard gage for depth measurement.
Optional longer extension bases are available. (Except for models with measuring ranges of 600 and 1000mm)

SPECIFICATIONS

Metric

Order No.	Range	Vernier reading	Accuracy	Base (W x T)	Remarks
527-201	0 – 150mm	0.05mm	±0.05mm	100 x 6.5mm	—
527-202	0 – 200mm		±0.05mm		—
527-203	0 – 300mm		±0.08mm		—
527-204	0 – 600mm		±0.10mm	250 x 10mm	—
527-205	0 – 1000mm		±0.15mm	250 x 10mm	—

Metric

Order No.	Range	Vernier reading	Accuracy	Base (W x T)	Remarks
527-101	0 – 150mm	0.02mm	±0.03mm	100 x 6.5mm	with fine adjsutment
527-102	0 – 200mm	0.02mm	±0.03mm	100 x 6.5mm	with fine adjsutment

Inch

Order No.	Range	Vernier reading	Accuracy	Base (W x T)	Remarks
527-111	0 – 6”	.001”	±.001”	3.93” x .25”	with fine adjustment
527-112	0 – 8”		±.001”	3.93” x .25”
527-113	0 – 12”		±.0015”	9.8” x .39”
527-114	0 – 24”		±.002”
527-115	0 – 40”		±.003”

DIMENSIONS

Coolant proof models achieve IP67 protection level.
Enables stable depth measurement with a resolution of 0.01mm.
ABSOLUTE Digital Caliper (Refer to page D-8 for ABSOLUTE function.)
Sliding operation of models with the measuring ranges 150mm (6″), 200mm (8″) and 300mm (12″) is smooth and comfortable.
Battery: SR44 (1 pc), 938882. For initial operational checks (standard accessory)
Optional longer extension bases are available. (Except for models with measuring ranges of 600, 750, 1000mm)

SPECIFICATIONS
Metric

Order No.	Range	Accuracy*	Repeatability	Base (W x T)	Battery life
571-211-30	0 – 150mm	±.001″/±0.02mm	0.01mm	100 x 6mm	5years
571-212-30	0 -200mm	±.001″/±0.02mm			5years
571-213-10	0 – 300mm	±.0015″/±0.03mm			3.5years
571-261-10**	0 -150mm	±.001″/±0.02mm			3years
571-262-10**	0 – 200mm	±.001″/±0.02mm			3years
571-263-10**	0 – 300mm	±.0015″/±0.03mm			1years
571-214-10	0 -450mm	±.002″/±0.05mm		250 x 10mm	3years
571-215-10	0 – 600mm	±.002″/±0.05mm
571-216-10	0 – 750mm	±.0025″/±0.06mm
571-217-10	0 – 1000mm	±.0025″/±0.07mm

* Excluding quantizing error
** IP67 Coolant Proof model

Inch/Metric

Order No.	Range	Accuracy*	Repeatability	Base (W x T)	Battery life
571-211-30	0 – 6”	±.001″/±0.02mm	0005″/ 0.01mm	3.93” x .23”	5years
571-212-30	0 – 8”	±.001″/±0.02mm			5years
571-213-10	0 – 12”	±.0015″/±0.03mm			3.5years
571-261-10**	0 – 6”	±.001″/±0.02mm			3years
571-262-10**	0 – 8”	±.001″/±0.02mm			3years
571-263-10**	0 – 12”	±.0015″/±0.03mm			1years
571-214-10	0 – 18”	±.002″/±0.05mm		9.8” x .39”	3years
571-215-10	0 – 24”	±.002″/±0.05mm
571-216-10	0 – 30”	±.0025″/±0.06mm
571-217-10	0 – 40”	±.0025″/±0.07mm

* Excluding quantizing error
** IP67 Coolant Proof model

DIMENSIONS

Optional accessories for IP67 coolant proof models
For details, refer to page D-39. Connecting cables
05CZA624: SPC cable with data button (1m)
05CZA625: SPC cable with data button (2m)

USB Input Tool Direct
06ADCV380A: SPC cable for USB-ITN-B (2m)
Connecting cables for U-WAVE-T
02AZD790A: SPC cable for U-WAVE with data button (160mm)
02AZE140A: SPC cable for footswitch

Optional accessories for other than IP67 coolant proof models
For details, refer to page D-39.
959143: Data hold unit Connecting cables for IT/DP/MUX
959149: SPC cable with data button (1m)
959150: SPC cable with data button (2m)
USB Input Tool Direct
06ADV380C: SPC cable for USB-ITN-C (2m)
Connecting cables for U-WAVE-T
02AZD790C: SPC cable for U-WAVE with data button (160mm)
02AZE140C: SPC cable for footswitch

Measuring rod diameter: ø4mm
Measuring rod lock is attached.
*Measuring rod is attached on the rear side of the micrometer.
Carbide-tipped measuring rod model is available.
Ratchet stop provides constant measuring force.

SPECIFICATIONS

Metric

Order No.	Range	Graduation	Base
128-101	0 – 25mm	0.01mm	63.5 x 16mm
128-103*1			63.5 x 16mm
128-102			101.6 x 16mm
128-104*1			101.6 x 16mm

*1 with carbide-tipped measuring rod

Inch

Order No.	Range	Graduation	Base
128-105	0 – 1”	.001″	2.5” x .63”
128-106	0 – 1”	.001″	4” x .63”

Technical Data

Accuracy: ±3μm (±.00015”) Flatness of reference face:
1.3μm (.00005”) for 63.5mm (2.5”) length base, 2μm (.00008”) for 101.6mm (4”) length base
Flatness of measuring spindle face: 0.3μm